Tag: cisco

Configure Cisco Wireless AP as controller

https://www.cisco.com/c/en/us/td/docs/wireless/controller/technotes/8-2/b_Mobility_Express_Deployment_guide/b_Mobility_Express_Deployment_guide_chapter_01.html

Настройка Cisco WLC 2504

https://ciscomaster.ru/content/nastroyka-cisco-wlc-2504
https://habr.com/ru/post/148903/
https://telecom-sales.ru/content/stati/nastrojka-kontrollera-besprovodnoj-seti-cisco-air-ct2504/
Совместимость: https://www.cisco.com/c/en/us/td/docs/wireless/controller/release/notes/crn85mr8.html#supported-aps

Virtual Wireless LAN Controller Deployment Guide

https://www.cisco.com/c/en/us/td/docs/wireless/technology/mesh/8-2/b_Virtual_Wireless_LAN_Controller_Deployment_Guide_8-2.html

Dynamic VLAN Assignment with WLCs based on ISE to Active Directory Group Mapping Configuration

https://www.cisco.com/c/en/us/support/docs/wireless/4400-series-wireless-lan-controllers/99121-vlan-acs-ad-config.html

https://netconfigure.net/index.php/ru/forum/12-konfiguratsiya-setevogo-oborudovaniya/182-nastrojka-cisco-wlc-flex-connect-h-reap-dynamic-vlan-assignment-microsoft-nps-radius

Cisco Aironet 2700 Series Access Points LED indication:

https://www.cisco.com/c/en/us/td/docs/wireless/access_point/2700/quick/guide/ap2700getstart.html#pgfId-37791

Простая, доступная и полезная Wi-Fi лаборатория:

https://habr.com/ru/post/352864/

Reset AP to factory defaults:

https://integratingit.wordpress.com/2018/07/01/reset-cisco-ap-to-factory-defaults/
Connect the console cable
Unplug the power or network cable if connected to a POE switch
Press and hold the Mode button
Plug the power back into the AP
Wait until the output on the console says "button is pressed. Wait for button to be released…"
Once that message is displayed release the button and allow the AP to boot
You should now be at the ap: prompt
Enter the command delete flash:private-multiple-fs
Press y when prompted
Type reset to reboot the AP
After the AP has rebooted login to the AP using the default username and password (the password is case sensitive)
Username: Cisco
Password: Cisco
The enable password is the same password.
Once logged in, the hostname of the AP should be the MAC address
On the WLC WebGUI, under the AP Join Stats you should be able to confirm that the MAC address of the AP is Joined.
If you do have access to the CLI of an AP but wish to reset the configuration, use either of the 2 commands below depending on the mode of the device CAPWAP/LWAPP:-
clear capwap private-config
clear lwapp private-config
reset


Cisco Wireless Solutions Software Compatibility Matrix:

https://www.cisco.com/c/en/us/td/docs/wireless/compatibility/matrix/compatibility-matrix.html

Converting Cisco Wireless Access Point from Lightweight Mode to Autonomous Mode and Vice Versa:

https://itthatshouldjustwork.blogspot.com/2015/08/convert-cisco-1702i-ap-to-autonomous.html
https://www.speaknetworks.com/converting-cisco-wireless-access-point-lightweight-mode-autonomous-mode-vice-versa/
https://www.cisco.com/en/US/docs/switches/lan/catalyst3850/software/release/3.2_0_se/multibook/configuration_guide/b_multibook_config_guide_wireless_3850_chapter_01101.pdf

Activate E-licences Cisco on wireless controller

https://web.archive.org/web/20170708123126/https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-0/configuration/guide/c70/c70ccfg.html

Automate wireless AP check and recovery

https://www.cisco.com/c/en/us/support/docs/wireless-mobility/wireless-lan-wlan/213317-understanding-various-ap-ios-flash-corru.html

Upload IOS image to the AP via TFTP

Connect console cable to the AP
Push reset button
Connect POE ethernet cable or power source to the AP
Hold reset button for 20 seconds until AP’s LED shine amber.

On the AP:

Initiale systems:
flash_init
ether_init
tftp_init

Upload the IOS image:
tar -xtract tftp://10.0.0.2/ap3g2-rcvk9w8-tar.default flash:

Set boot path:
boot=flash:/ap3g2-rcvk9w8-mx

Understand AP Radio Reset Codes

https://www.cisco.com/c/en/us/support/docs/wireless/aironet-3700-series/117869-technote-ap-00.html